New Hire Tech Rep Quiz QUIZ Question Title * Your Contact Information: Full name E-mail Phone Question Title * Contact information for your hiring manager Name E-mail Phone Question Title * When installing a new air drier system for compressed air, where should it be placed? Within 6 feet of the compressor In a cool, dark place At least 25 feet from the compressor Inside the paint booth Question Title * An HVLP air cap test gauge is used to measure which of the following: Fluid flow at the cap Air volume at the air cap Air pressure at the gun inlet Air pressure at the cap Question Title * Where is the appropriate location to regulate the atomization air coming into the spray gun? At the compressor Gun mounted cheater valve Wall Regulator Gun mounted regulator Question Title * A spray gun is spraying in an uneven spray pattern. This typically is caused by a dirty fluid tip or air cap. What would be the first step to diagnose whether this problem is caused by the fluid tip or the air cap? Rotate the air cap 180 degrees and spray a test pattern to see if the uneven pattern has rotated 180 degrees. Clean out all of the fluid passages of the spray gun and spray a test pattern. Take the air cap off and hold it up to the light to see if the holes in the air cap are clogged. Take the air cap off of the spray gun and visually inspect all areas for signs of contamination. Question Title * Which of the following best describes the air pressure condition that would cause the booth door to close by itself? Positive pressure Negative pressure Bipolar pressure Normal pressure Question Title * Which of the following will most likely lead to increased paint viscosity? Catalyzed paint that is nearing the end of its pot life High Humidity High Temperature Over reduction Question Title * Technician A says that all refinish primers can be used on any substrate. Technician B says that aerosol etch primer is the most convenient for large bare metal areas. Which technician is correct? Technician A Technician B Both Technician A and B Neither Technician A nor B Question Title * Which factors affect waterborne basecoat dry times? Air movement Humidity Film build All of the above Question Title * If the PPG product you are using has more than one catalyst to choose from, what would affect your choice? Ambient temperature Spray gun being used Time of day Relative humidity Question Title * Adding an accelerator to a product mix can affect which of the following characteristics? Atomization Substrate compatibility Film build Pot life Question Title * Which of the following is recommended if you determine a replacement part is covered with a 1K primer? Nothing needs to be done Remove all of the 1K primer Re-prime the part with another 1K product Return the part to the manufacturer Question Title * Waterborne basecoat requires which flex additive when applied over flexile substrates? DX814 D814 SX814 Waterborne basecoat does not require a flex additive. Question Title * To restore the best corrosion resistance and adhesion properties to a panel, which of the following should be applied? A high-build surfacer An etch primer A catalyzed basecoat A tinted undercoat Question Title * Why is it necessary to determine the type of substrate you are refinishing? It is not important to identify what type of substrate is being refinished. Clearcoats will have varying levels of gloss on different substrates. To document the type on the warranty paperwork. Different substrates may require different procedures. Question Title * Using good spray gun techniques such as speed, path and distance, helps a technician obtain which of the following? Corrosion protection Proper film build Dirt-free finish Additional gloss Question Title * How long should the solvent basecoat mixing banks be agitated for the first time they are started in the morning? 15 minutes 20 minutes 30 minutes 1 hour Question Title * It is recommended that new solvent basecoat toners are placed on an agitator for how long prior to putting on a mixing bank? 5 minutes 15 minutes 20 minutes 30 minutes Question Title * Technician A says that a newly-mixed PPG waterborne basecoat formula should be placed on a shaker for at least 20 minutes before using. Technician B says that a new PPG waterborne basecoat toners should be placed on a shaker for at least 5 minutes before using. Which Technician is correct? Technician A Technician B Both Technician A and B Neither Technician A nor B Question Title * Which of the following is recommended to use for cleaning a TouchMix™ screen? Razor blade Soap and water Wax and grease remover Lacquer thinner Question Title * Technician A says that it is recommended to use only the toners listed in the formula when mixing a color. Technician B says that it is okay to substitute a toner when tinting if it is or a small quantity. Which Technician is correct? Technician A Technician B Both Technician A and B Neither Technician A nor B Question Title * A red solid color may only move towards blue and what other color? Yellow Green Lime Teal Question Title * Which of the following application variables does NOT directly affect the color of a metallic basecoat? Reduction/mix ratio of the basecoat Size of the repair panel Fluid tip, needle and air cap used PSI at the spray gun air cap Question Title * In a tri-stage repair, which coat is used to achieve hiding? The clearcoat The midcoat The groundcoat The undercoat Question Title * Which of the following light sources will provide the best lighting for checking a color match? Sodium light Natural daylight Fluorescent light Incandescent light Question Title * The effect that occurs when a color appears differently under another light source is known as: Variance Flop Metamerism Shifting Page1 / 1 100% of survey complete. Submit Quiz