Level 1 Inspector Certification Sample Test

Question Title

* 1. Which of the following is necessary for a contract to be enforceable?

The performance of the work or services must be legal in the applicable jurisdictions

An attorney must have written or reviewed the contract

All parties involved must be present at the time the contract is signed

All of the above

Question Title

* 2. On completed construction projects, who is normally responsible for ensuring that the installation complies with the provided drawings and/or building codes during a commission inspection?

The contractor

The commissioning inspector

The architect or Engineer

B or C

Question Title

* 3. Who is the BEST person to contact if the working drawings, blueprints, or supplemental documentation are unclear during the process of inspection?

The element / ride owner

The local code enforcement officer

The local building inspector or zoning compliance officer

The Manufacturer of the structure being inspected

Question Title

* 4. Which of the following best describes an insurance policy?

An agreement whereas the insurer guarantees that the contractor will not be sued by any
party

A policy that is in no way related to a contract to perform services

A contract under which the contractor/inspector agrees to perform a certain amount of work
for a specified payment

A contract under which the underwriter promises to assume financial responsibility for a
specified loss or liability incurred by the insured party.

Question Title

* 5. 3/8” converted to a decimal fraction is:

.333

.375

.398

.38

Question Title

* 6. .25 converted to a fraction is:

2/5

1 /4

4/8

1/8

Question Title

* 7. A meter is a basic unit of length. A Kilometer is _________ meters

100

1,000

Question Title

* 8. To convert Inches to Centimeters you would need to multiply the number of inches by _______?

0.394

2.54

0.348

None of the Above

Question Title

* 9. 1 foot = how many centimeters?

4.728

30.48

4.176

Question Title

Use the image below to identify the marks on this Imperial Ruler for questions 10 and 11

Question Title

* 10. “B” is?

1/32”

1/16”

1/4”

7/8”

Question Title

* 11. “D” is?

1”

1-3/4”

1-7/8”

1-13/16”

Question Title

Use the image below to identify the marks on this Metric Ruler for questions 12 and 13

Question Title

* 12. A is?

1 cm

0 cm

1 mm

1 km

Question Title

* 13. C is?

1.4 cm

1.7 cm

1.7 mm

17 cm

Question Title

* 14. 1 yard = how many ft.

Question Title

* 15. What is the AREA of an object in square ft. with a width of 48” and a length of 96”?

Question Title

* 16. What is the perimeter of an object in feet where the width is 96” and the length is 96”

142

Question Title

* 17. On a set of working drawings, a “section’ or “cross-section” of an object or structure would best be described as:

The object or structure sliced into two parts with one part removed

he object or structure shown in a larger scale so as to provide greater detail.

A specific section of the object or structure shown separately

All of the above

Question Title

* 18. A supplemental drawing used with a conventional working drawing that gives a complete and more exact description of the items in use is called the:

Title Block

Detail Drawing

Schedule

Riser Diagram

Question Title

* 19. A site plan is a plan view (as viewed from above) that shows

Each level of the structure

Power riser diagrams

Cross sections of the structure

Property boundaries, buildings, roads, and elevation marks.

Question Title

* 20. On a set of working drawings, where is the drawing scale most likely to be shown?

In the symbols list

In the written specifications

In the fastener and attachment schedule

In the title block

Question Title

* 21. A legend of symbols list is shown on construction drawings to:

Describe materials, installation methods and scale being used on the drawings

Show the outline of the structures assembly steps

Identify and define all symbols used on the drawings

Enable the electrical service size to be calculated

Question Title

* 22. If blueprints show fastener attachments, why can’t the contractor have just used the cheapest fasteners they could find?

This is exactly what the builder should have done.

The written specifications may demand a specific grade or coated fastener as well as size to
meet a standard, local building code and or corrosion resistance.

This would be a contract violation

Because blueprints do not specify cost

Question Title

Use the symbol below for Question 23

Question Title

* 23. The bottom letter and number of the symbol above identify what?

South view drawing specification

North view sheet type

The sheet number

The part Identifier and quantity

Question Title

Use the Image below for Question 24

Question Title

* 24. The illustration above is called a?

Title Block

Project Ledged

Revision schedule

Title legend

Question Title

* 25. Which of these is meant to be tightened by hand

Machine Screw

Wood Screw

Wing Nut

Bolt

Question Title

* 26. Which of these typically does not require a tool to install

Lag Bolt

Wire rope clip

Spring Pins

All of the above

Question Title

* 27. Which tool below is best to tighten a bolt?

Pliers

Chanel Locks

Vice Grip

Combination Wrench

Question Title

* 28. What is the best tool for assessing that a 10’ vertically oriented wood pole is straight up and down?

Ruler

Level

Square

Plumb Bob

Question Title

Using the illustration please identify what numbered shape in the top row is the same as
the shape with a letter in the bottom row.

<strong>Using the illustration please identify what numbered shape in the top row is the same as</strong><br><strong>the shape with a letter in the bottom row.</strong>

Question Title

* 29. 1=

Question Title

* 30. 6=

Question Title

Use this Image for Question 31.

Question Title

* 31. Select the appropriate choice from the bottom row to complete the sequence in the top row.

Question Title

* 32. A lockout tag is used to

Identify a ride or element that shall not be used as assessed by in-house maintenance staff

Identify a ride or element that shall not be used as assessed by a qualified third party
inspector

Shall not be removed until the issue causing the use of the lockout tag has been fixed and
properly tested.

All of the above

Question Title

* 33. Personal Fall protection equipment shall be used by staff when

Required by law

Required by company policy

When the employee is uncomfortable completing the task without the equipment.

All of the above

Question Title

* 34. Personal Fall Protection Equipment shall be inspected at least

Before use

Weekly

Monthly

Annually

Question Title

* 35. Acceptable Fall Protection for an Inspector includes

A railing 42” or higher

A full body harness with appropriate lanyard

A net below or installed as a perimeter around a work area

All of the above

Question Title

* 36. SAE is an identifying mark of a fastener that was made to what standard?

Society of Automotive Engineers

Society of Accredited Electricians

Is not an acronym for an organization but a chemical grade for the metal used in the
manufacturing of the component?

None of the above

Question Title

* 37. Which of the following statements is FALSE about markings on SAE fasteners?

Markings must be visible and can be placed in any location on bolt

3 lines for grade 5 fasteners

6 lines for grade 8 fasteners

Provide a visual identifier that lets inspectors know the anticipated strength of the fastener

Question Title

* 38. Metric Fasteners have a number on the head such as 8.8 or 12.9. This mark?

Identifies the size of the fastener

Identifies the strength of the fastener

Identifies the material of the fastener

None of the above.

Question Title

* 39. Tensile Strength can best be described as?

The angled force that a component can withstand before breaking

The force applied in-line to pull a component to the point it breaks

The shear force that a component can withstand before breaking

The opposite of compressive force

Question Title

* 40. Torque is NOT?

The tendency of a force to cause rotation

Wrench tight

measured in Ft. Pounds or Newton Meters

A specification provided by a fastener manufacturer for best performance of product

Question Title

* 41. Heat Treatment

Is a process used to alter the physical and/or chemical properties of a material

Can relieve internal stresses and refine structures to improve their cold working properties

A process that toughens a metallic piece

Both A and B

Question Title

* 42. Welding is defined as?

The melting of a lower-melting point material between two work pieces to form a bond
between them, like soldering

A process that can be substituted with bolts in the field even if welding is required by stamped
blueprints

Capable of bonding any type of metal to any other type of metal, (i.e. copper to aluminum,
stainless steel to nickel, aluminum to platinum, etc.).

Join together (metal pieces or parts) by heating the surfaces to the point of melting using a blowtorch, electric arc, or other means, and uniting them by pressing, hammering, etc.

Question Title

* 43. Which is NOT a type of Non-Destructive Testing?

A visual weld inspection that looks for abnormalities in materials

A magnet used to detect surface defects on ferrous materials

The use of a Tension Meter to check wire rope tension

Pulling a component to failure to determine its ultimate strength

Question Title

* 44. The components of wire rope include?

Core

Strand

Wire

All of the above

Question Title

* 45. Examples of damage to wire rope that would compromise its ability to function appropriately include

Kinking or kink

Bird caging

Excessive corrosion

All of the above

Question Title

* 46. When inspecting a wire rope lifeline where the crown surface wires are worn by 1/3 or more of the original diameter the cable shall fail inspection.

True

False

Question Title

* 47. If there are 133 wires in 3/8” 7x19 GAC and the breaking strength is listed by the manufacturer as 14,400 lbs. and one strand of wires is completely broken what is the estimated breaking strength of the wire rope in service?

9,886 Lbs.

10,286 Lbs

12,342 Lbs.

7,800 Lbs.

Question Title

* 48. ANSI B77.1 is a standard that deals with

The design of welded components

The design manufacture and maintenance of passenger transportation systems that use
cables, ropes or other flexible elements that is frequently referenced for commercial zip lines in
state amusement codes.

The design manufacture and maintenance of gas and electric powered amusement rides

None of the above

Question Title

* 49. The ASTM collection of standards for amusement rides is frequently referred to as the

A-2291 Standards

F-24 Standards

AWS-15 Standards

ANSI 620 standards

Level 1 Inspector Certification Sample Test

Question Title

* 1. Which of the following is necessary for a contract to be enforceable?

Question Title

* 2. On completed construction projects, who is normally responsible for ensuring that the installation complies with the provided drawings and/or building codes during a commission inspection?

Question Title

* 3. Who is the BEST person to contact if the working drawings, blueprints, or supplemental documentation are unclear during the process of inspection?

Question Title

* 4. Which of the following best describes an insurance policy?

Question Title

* 5. 3/8” converted to a decimal fraction is:

Question Title

* 6. .25 converted to a fraction is:

Question Title

* 7. A meter is a basic unit of length. A Kilometer is _________ meters

Question Title

* 8. To convert Inches to Centimeters you would need to multiply the number of inches by _______?

Question Title

* 9. 1 foot = how many centimeters?

Question Title

Use the image below to identify the marks on this Imperial Ruler for questions 10 and 11

Question Title

* 10. “B” is?

Question Title

* 11. “D” is?

Question Title

Use the image below to identify the marks on this Metric Ruler for questions 12 and 13

Question Title

* 12. A is?

Question Title

* 13. C is?

Question Title

* 14. 1 yard = how many ft.

Question Title

* 15. What is the AREA of an object in square ft. with a width of 48” and a length of 96”?

Question Title

* 16. What is the perimeter of an object in feet where the width is 96” and the length is 96”

Question Title

* 17. On a set of working drawings, a “section’ or “cross-section” of an object or structure would best be described as:

Question Title

* 18. A supplemental drawing used with a conventional working drawing that gives a complete and more exact description of the items in use is called the:

Question Title

* 19. A site plan is a plan view (as viewed from above) that shows

Question Title

* 20. On a set of working drawings, where is the drawing scale most likely to be shown?

Question Title

* 21. A legend of symbols list is shown on construction drawings to:

Question Title

* 22. If blueprints show fastener attachments, why can’t the contractor have just used the cheapest fasteners they could find?

Question Title

Use the symbol below for Question 23

Question Title

* 23. The bottom letter and number of the symbol above identify what?

Question Title

Use the Image below for Question 24

Question Title

* 24. The illustration above is called a?

Question Title

* 25. Which of these is meant to be tightened by hand ﻿

Question Title

* 26. Which of these typically does not require a tool to install

Question Title

* 27. Which tool below is best to tighten a bolt?

Question Title

* 28. What is the best tool for assessing that a 10’ vertically oriented wood pole is straight up and down?

Question Title

Using the illustration please identify what numbered shape in the top row is the same asthe shape with a letter in the bottom row.

Question Title

* 29. 1=

Question Title

* 30. 6=

Question Title

Use this Image for Question 31.

Question Title

* 31. Select the appropriate choice from the bottom row to complete the sequence in the top row.

Question Title

* 32. A lockout tag is used to

Question Title

* 33. Personal Fall protection equipment shall be used by staff when

Question Title

* 25. Which of these is meant to be tightened by hand

Using the illustration please identify what numbered shape in the top row is the same as
the shape with a letter in the bottom row.